“How to Apply a Lace Front Wig: A Step-by-Step Guide” is a collaborative post.
Lace front wigs have become increasingly popular for their natural look and versatility. Whether you’re wearing a wig for fashion, convenience, or medical reasons, knowing how to apply it correctly ensures a seamless and secure fit. This guide will walk you through the process step by step, from preparation to final styling.
Step 1: Gather Your Supplies
Before you begin, make sure you have all the necessary tools:
- A Sunber Hair lace front wig
- Rubbing alcohol or scalp cleanser
- Wig cap
- Scissors
- Wig adhesive (glue or tape)
- Blow dryer (optional)
- Edge brush or small toothbrush
- Foundation or lace tint spray
- Wide-tooth comb or wig brush
- Hair clips
- Styling products (optional)
Step 2: Prep Your Natural Hair
For a flat and natural look, your natural hair should be prepped properly.
- If you have short hair, simply brush it back and wear a wig cap.
- If you have long hair, braid it into cornrows or small flat braids, then wear a wig cap to secure everything.
- Use rubbing alcohol or a scalp cleanser to remove excess oil from your forehead and hairline. This helps the wig adhesive bond better.
Step 3: Wear a Wig Cap
A wig cap helps to keep your natural hair in place and creates a smooth surface for the wig.
- Choose a wig cap that matches your skin tone for a more natural appearance.
- Pull the cap down over your head and adjust it so that it sits just behind your natural hairline.
- Use foundation or lace tint spray to blend the cap with your skin tone if needed.
Step 4: Trim the Lace
Most lace front wigs come with excess lace that needs to be trimmed for a perfect fit.
- Put the wig on your head and adjust it to align with your natural hairline.
- Use clips to hold the hair away from the lace.
- Using small, sharp scissors, carefully cut the lace along your natural hairline in small sections to avoid jagged edges.
- Leave a tiny bit of lace to blend into your skin, but not too much to make it noticeable.
Step 5: Apply the Adhesive
You can use either wig glue or tape to secure your lace front wig.
- For wig glue: Apply a thin layer of adhesive along your hairline and let it become tacky (about 30-60 seconds). If using a strong adhesive, you may need to apply multiple layers.
- For wig tape: Cut small pieces and place them along the hairline, pressing them firmly onto your skin.
- Once the adhesive is ready, gently press the lace down into place. Use a blow dryer on a cool setting to speed up the drying process.
Step 6: Secure and Style
- After applying the wig, gently press the lace into the adhesive with your fingers or the back of a comb.
- Wrap a silk scarf around your hairline for about 10-15 minutes to help the lace melt into your skin.
- Use a small brush or edge brush to lay down baby hairs if desired.
- Style your wig as you like—use heat styling tools if the wig is heat-resistant, or apply mousse and gel for a defined look.
Step 7: Finishing Touches
- Check the hairline in natural light to ensure it looks seamless.
- Use a bit of foundation or concealer along the lace to further blend it with your skin.
- If needed, pluck the hairline slightly to create a more natural effect.
- Spray a light mist of holding spray or apply mousse to keep flyaways in place.
Maintenance Tips
To keep your lace front wig in great condition:
- Remove it carefully by using a wig adhesive remover.
- Wash it every 10-15 wears using a sulfate-free shampoo and conditioner.
- Store it on a wig stand or mannequin head to maintain its shape.
- Avoid excessive heat styling to extend the wig’s lifespan.
Final Thoughts
Applying a lace front wig may seem intimidating at first, but with practice, it becomes easier. By following these steps, you can achieve a flawless, natural-looking result. Whether you’re wearing it for a special occasion or daily use, a properly applied lace front wig can boost your confidence and enhance your overall look.
